Geekstory BN-220 Dual GPS Glonass Module Navigation+GPS Passive Antenna with Flash TTL Level for Arduino Raspberry Pi Pixhawk F3 CC3D Betaflight F4 Flight Control(Pack of 2PCS)
    

 Description
  
Specification Receiving Format :
GPS,GLONASS,Galileo,BeiDou,QZSS and SBAS Frequency : GPS L1,GLONASS L1,BeiDou
B1,SBAS L1,Galileo E1 Channels : 72 Searching Channel Sensitivity Tracking :
-167dBm, Reacquisition : -160dBm Cold start : -148dBm, Hot start : -156dBm
Accuracy Position Horizontal : 2.0 m CEP 2D RMS SBAS Enable (Typical Open Sky)
Velocity : 0.1m/sec 95% (SA off) Timing : 1us synchronized to GPS time
Acquisition Time Cold Start : 26s, Warm start : 25s, Hot start : 1s Data and
Update Rate Support Rate : 4800bps to 921600bps,Default 9600bps Data Level :
TTL or RS-232,Default TTL level Data Protocol : NMEA-0183 or UBX, Default
NMEA-0183 Single GNSS : 1Hz-18Hz Concurrent GNSS : 1Hz-10Hz,Default 1Hz
Operational Limits Altitude : 50,000m Max, Velocity : 515m/s Max, Acceleration
: Less than 4g Power consumption VCC : DC Voltage 3.0V-5.5V,Typical: 5.0V
Current : Capture 50mA/5.0V Operating temp : -40 �8C to +85�8C Storage Temp :
-40�8C to +105�8C Indicator: TX LED:blue.The data output, TX LED flashing PPS
LED:red.PPS LED not bright when GPS not fixed,flashing when fixed Wiring:
GND,TX output,RX input,VCC(3.0v-5.5v) NMEA message output sample
GNRMC,073114.00,A,2237.56240,N,11401.59614,E,1.329,21.11,020916,,,A,V37
GNVTG,21.11,T,,M,1.329,N,2.462,K,A1B
GNGGA,073114.00,2237.56240,N,11401.59614,E,1,12,0.78,112.9,M,-2.5,M,,54
GNGSA,A,3,19,05,02,06,17,12,09,13,,,,,1.48,0.78,1.26,101
GNGSA,A,3,69,83,84,70,68,82,,,,,,,1.48,0.78,1.26,20E
GPGSV,4,1,13,02,46,340,36,05,52,254,37,06,42,041,41,09,22,053,40,06E
GPGSV,4,2,13,12,32,282,35,13,13,185,33,17,36,131,37,19,57,119,44,066
GPGSV,4,3,13,20,03,237,,23,00,038,,25,09,311,19,42,51,128,32,060
GPGSV,4,4,13,50,46,123,33,050
GLGSV,2,1,08,68,25,027,39,69,78,011,36,70,40,213,43,74,00,259,,078
GLGSV,2,2,08,82,06,124,36,83,46,085,44,84,44,358,41,85,05,324,14,074
GNGLL,2237.56240,N,11401.59614,E,073114.00,A,A7C BN 220 GPS connection to
flight controller VCC to 5V RX to TX3 TX to RX3 GND to GND betaflight Software
Set up GPS module with betaflight Software BN 220 GPS connection to sensor VCC
to 5V RX to D4 TX to D3 GND to GND Read more BN-180 GPS BN-220 GPS BN-800 GPS
BN-880 GPS Flash No 4M Flash 4M Flash 4M Flash Compass No No HMC5883L HMC5883L
Antenna Type Passive Passive Passive Active Defaut Working Mode GPS+GLONASS
GPS+GLONASS GPS+GLONASS GPS+GLONASS Voltage 3.6-5.5V 3.6-5.5V 3.6-5.5V
3.6-5.5V Default Baudrate 9600 9600 9600 9600 Frequency Range 1-10HZ 1-10HZ
1-10HZ 1-10HZ Output TTL TTL TTL TTL Pin Header GND,TX,RX,VCC GND,TX,RX,VCC
SDA,GND,TX,RX,VCC,SCL SDA,GND,TX,RX,VCC,SCL Connector 1.0mm pitch 4P 1.0mm
pitch 4P 1.25mm pitch 6P 1.25mm pitch 6P GPS Modules Comparison BN-180 GPS
Module Size: 18186mm BN-220 GPS Module Size: 22206mm BN-880 GPS Module
Size: 282810mm BN-800 GPS Module Size: 35356mm
  
Features:
  

    
When it is used on Raspberry Pi, it is not necessary to install the driver, but the software must be installed
The TX LED flash means gps module output normally.The PPS LED flash means gps module locate your place.
Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable
You will get 2pcs BN-220 GPS module,each module with 3pcs cable. Any problem please click Geekstory(you can find "Sold by Geekstory" under Buy Now button), in the new page, click Ask a question to email us